News-Hangzhou Dachao Pump Manufacturing Co., Ltd

dachao

dachao

Maintenance methods for carbon black equipment

Maintenance methods for carbon black equipment

Carbon black equipment can complete mixing, humidification, granulation and other processes in one go, so this product is now suitable for industries such as pharmaceuticals, food, and chemical. It meets the GMP requirements for drug production and has the characteristics of high efficiency, high quality, low consumption, no pollution, and safety. Below is an introduction to the maintenance methods for carbon black equipment? Qingdao carbon black equipment should be placed in a dry and clean room during maintenance, and the atmosphere should not contain corrosive gases such as acid flowing to machine components. If the machine is not in use for a long time, the entire body of the machine must be wiped clean, and the smooth surface of the machine parts should be coated with anti rust oil and covered with a cloth. Here is a reminder to everyone that it is necessary to regularly inspect the machinery, once a month, to check whether the moving parts of Qingdao carbon black equipment, such as worm gears, worms, bearings, etc., are flexible and worn. If defects are found, they should be repaired in a timely manner. It should not be used for free. After using the Qingdao carbon black equipment once or during shutdown, the drum should be removed for cleaning, and the remaining powder in the bucket should be cleaned, and then installed for future use. Usually, equipment components are inspected once a month, mainly including the flexibility and wear of moving parts such as worm gears, worms, bearings, etc. Place it in a clean room to avoid the impact of acid and corrosive gases on the equipment. What Qingdao carbon black equipment needs to do during maintenance is to regularly inspect the parts, and also to regularly check whether the sturdy components of each moving component are loose. If there is looseness, it should be immediately tightened and adjusted or replaced if necessary to ensure a secure connection. Add grease to the bearings every six months, and the amount used should not exceed 2/3 of the bearing space. It is also necessary to keep the equipment surface clean and free of debris. During cleaning, do not splash water onto the equipment control panel. Regular maintenance personnel conduct detailed inspections and maintenance of the equipment, promptly repair or replace any faults found, to ensure that the Qingdao carbon black equipment is in good condition. Now it is our factory's flagship product. Thank you for the strong support of new and old customers. While ensuring the reliability of product quality, we also benefit our customers. If you have any technical questions about the product, you can always come here for consultation. This product can achieve one-step mixing and granulation during operation. It can automatically discharge materials. Low energy consumption and high quality. Save the amount of adhesive used. The equipment occupies a small area and is easy to place. In this way, its lifespan can be extended.

15

2021

/

09

The purpose of carbon black equipment

The purpose of carbon black equipment

The manufacturer of carbon black equipment stated that the main purpose of carbon black equipment is to write adhesive wet particles into food, chemical and other professional powders for granulation. What is the purpose of carbon black equipment? I hope you can bring some better help when choosing in the future. 　　The carbon black equipment mainly consists of the body, granulation device, screen tube, gearbox, motor, etc. The body of the carbon black equipment is a separate rectangular body, composed of a base, a bearing frame, and a gearbox. The feed hopper is connected to the bearing frame and extends out of the machine. The body does not need to be installed and can be placed indoors at will; Hinge one end with a nut; Another important point is that both the front and rear of the drum are equipped with bearing brackets located below the hopper. The two ends of the drum adopt symmetrical convex couplings, which are not restricted by inversion and are easy to disassemble. The screen clips are located on both sides of the drum and are made of steel pipes. There is a long groove in the middle of the steel pipe. The gearbox is mainly driven by a worm gear, and the outer end of the worm gear is equipped with an eccentric rod, which is used to drive the gear rod to move back and forth, while the gear shaft that meshes with the gear rod rotates in the opposite direction. Nowadays, high-speed rotation and shearing are mainly used for granulation. The transmission shaft of carbon black equipment is sealed with a large amount of air, which can be replaced with water during cleaning. Fluidized granulation, material is nearly spherical and has good fluidity. Carbon black equipment has a small footprint and low cost; The cost required for the entire granulation process is low; The granulation process is relatively simple and has low energy consumption; Using a sealed environment for treatment, there is no pollution, and the finished product is relatively hygienic. Especially when using carbon black equipment, the granulation time is greatly shortened, and the entire mixing granulation process can be completed in a few minutes. Mixing and cutting can be easily adjusted, suitable for granulation of different raw materials and needs. The manufacturer also adopts PLC human-machine interface control technology during production, which is simple and convenient to control. The operation process is completely enclosed without any pollution. Smooth operation and low noise. Inflatable sealed drive shaft design for easy cleaning. In order to extend its service life, check the parts of the carbon black equipment once a month, mainly including the moving parts of worm gears, worms, bearings, etc., for flexibility and wear. succedaneum; Usually, it should be placed in a dust-free room to avoid the impact of acids, corrosive gases, etc. on the equipment; After use or during shutdown, the drum should be removed, cleaned, and then installed in place.

15

2021

/

09

Advanced processing equipment

Advanced processing equipment

Qingdao Haiguangli Machinery Manufacturing Co., Ltd. was established in September 2006 with a registered capital of 2 million yuan. It is located in Jiaobei Industrial Park, Jiaozhou, close to Tongsan Expressway, Jiqing Expressway, and Jiaozhou Bay Ring Expressway. Jiaoji Railway runs through the city with convenient transportation. The company covers an area of 10000 square meters and currently has 50 employees, including 1 senior engineer and 3 engineers; 10 certified welders, 1 crane operator, 1 electrician, 5 fitters and 5 plumbers each; 1 full-time inspector. 公司是一家以炭黑设备设计与制造为主的企业，有一批炭黑行业专业技术人员，技术力量雄厚，经验丰富，有雄厚机械加工能力。自2006年成立以来，与国内多家炭黑生产厂家进行合作，主要产品：湿法造粒机、高温空气预热器、提升机、螺旋输送器、气密阀、筛选机、三通阀等。尤其在湿法造粒机方面，取得了技术突破，赢得了用户好评。 The company is an enterprise mainly engaged in the design and manufacturing of carbon black equipment, with a group of professional technical personnel in the carbon black industry, strong technical strength, rich experience, and strong mechanical processing capabilities. Since its establishment in 2006, we have cooperated with multiple domestic carbon black manufacturers, mainly producing wet granulators, high-temperature air preheaters, elevators, spiral conveyors, airtight valves, screening machines, three-way valves, etc. Especially in the field of wet granulation machines, technological breakthroughs have been made and user praise has been won. The company adheres to the business philosophy of "business is humanity", adheres to maintaining reputation through service, strives for survival through quality, and promotes development through innovation. Adhering to the principle of "reputation first and user first", we wholeheartedly serve the vast number of users and strive to manufacture products that are reassuring to the country and satisfying to users.

15

2021

/

09

< 1 2 >

Company Profile

Wet granulation machine

Tel：086-571-86011822

fax: 086-571-86019722

Address: No. 9, No.7 Road, Dongzhou Industrial Functional Zone, Fuyang, Hangzhou, China

Copyright: Hangzhou Dachao Pump Manufacturing Co., Ltd

powered by www.300.cn SEO | business license